It will be used to store the current value of Pdelay Request Interval.
It will be represented as power of two in seconds.
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Make port_signaling_construct() to create a generic signaling
ptp_message. Move the unicast specific code to
port_signaling_uc_construct().
This is done to support the creation of Message Interval Request TLV (as
defined in 802.1AS Section 10.5.4.3). This TLV can be used to request
change in Announce Interval, Sync Interval or Link Delay Interval on a
remote system.
[ RC - fix trivial rebase conflict on top of targetPortIdentity check. ]
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
IEEE 1588 specifies dropping signaling messages if the
targetPortIdentity does not match the receiving port. Up until now
the unicast code did check that field, but only for the unicast
transmission request and cancel operations.
This patch moves the target port identity check so that it applies to
each and every received signaling message.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Ever since commit d88b4ff229 ("util: Added IPv6 support in help
funtions addreq and str2addr"), the unicast master table supports
entries with IPv6 addresses. This patch updates the man page to
reflect this fact.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
In logic, when we want to switch phc, we should check if the new phc
index is valid instead of checking the previous one.
In reality, if we use linux team interface with activebackup mode. As
teamd is a userspace tool, it sets the new slave as active port after
receiving link change message. If we set current active port down and
another slave up. There is a race that we receive the new slave's link
up message while active port(ts_index) is still the old one. This means
we may use a link down interface as ts_index and get phc_index with -1.
If we update the p->phc_index to -1, there will be no possibility to
change it back to other value as we swith phc only when p->phc_index >= 0.
With this fix, we will not switch phc_index until receiving the real
active port(p->iface->ts_info.phc_index >= 0) update message.
Reported-by: Miroslav Lichvar <mlichvar@redhat.com>
Fixes: 536a71031d ("ptp4l: use ts label to get ts info")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
The manpage for recvmsg says -1 will be returned on error, Zero indicates an
"orderly shutdown", presumably only in case of stream sockets.
Further, UNIX Network Programming, Vol 1 says ".. a return value of 0 from
recvfrom is acceptable for a datagram protocol"
Such packets have been observed in the wild, aimed at PTP's multicast
address and port, possibly related to malformed management queries.
Patch to properly check return from recvmesg and not trigger the fault
codepath. Instead, such packets are treated as "Bad Message" the same as
non-zero but still too-short UDP payloads.
Signed-off-by: David Mirabito <davidjm@arista.com>
Commit c8107c8d ("config: Add a configuration option for TC mode.")
added a new TC mode. An early version of the patch series included a
new '-t' command line option, but this was dropped considering the
fact that long options are always available. IOW the TC user can
simply add '--clock_type=P2P_TC' to the command line, making the
single dash option redundant.
This patch fixes the misleading usage message by removing the
non-existing option.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Now that PTP support support is well established, remove the text that
attempts to explain the (at the time) incomplete kernel support. Instead
just give a couple of ethtool examples.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Adjust checks of logMessageInterval in received packet to prevent 1 of
type int being shifted by values >= 31.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
A clock that cannot be adjusted has no servo. Check if a servo is
present before updating the clock.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
If synchronizing a PHC to the system clock, use one of the
PTP_SYS_OFFSET ioctls (if supported) to measure the offset between the
two clocks. Negate the offset and switch the timestamp before passing
them to the servo.
This makes the synchronization between PHC and system clock symmetric.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
This is a more accurate variant of the the PTP_SYS_OFFSET ioctl, which
will probably be supported in future kernel versions.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
This ioctl uses cross timestamping for a more accurate measurement of
the offset. It is supported on some onboard Intel NICs using the e1000e
driver and a virtual PHC with the ptp_kvm driver.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
The kernel supports different PTP_SYS_OFFSET* ioctls. Use the sysoff
enum to allow selecting between them in sysoff_measure().
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Added check so that convertion from a positive tmv not result in a negative TimeInterval and vice versa.
Signed-off-by: Anders Selhammer <anders.selhammer@est.tech>
I have reduced the requirements for the -p option to accept
any type of device. With this it should be possible to use
ptp4l to syncronize any clock device that implements the kernel
POSIX clock interface.
[ RC - Initialize struct timex. ]
Signed-off-by: Dimitrios Katsaros <patcherwork@gmail.com>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
When inhibit_announce is set, ANNOUNCE_RECEIPT_TIMEOUT_EXPIRES event is
still sent once every state change. Avoid this by explicitly sending
EV_NONE instead.
[ RC - Simplify and keep all of the timer's state maintenance. ]
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
The "inhibit_announce" and "ignore_source_id" options were introduced
in order to support the automotive profile. That profile happens to
specify using the peer to peer delay mechanism, but there is no reason
to restrict them to that mechanism. As it now stands, enabling these
two options prevents E2E slaves from synchronizing. This patch fixes
the issue by checking the "ignore_source_id" option when accepting E2E
delay response messages.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
This commit adds example for configuring master and slave devices that
support features from the Automotive Profile.
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
This config option will skip the source port identity verification in
the Sync and Follow_up messages. This option is needed when the announce
messages are disabled because the slave cannot know the identity of
master without announce messages.
This is required by Automotive Profile as part of skipping the Best
Master Clock Algorithm (BMCA).
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
This option will accomplish 2 things. On the master, it will stop the
announce messages being sent (by disabling FD_MANNO_TIMER timer). On
slave, it will not configure announce message timeouts (by disabling
FD_ANNOUNCE_TIMEOUT timer).
This config option is needed for the Automotive profile as part of
skipping the Best Master Clock Algorithm (BMCA).
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
This adds config option to specify static roles for master and slave
in the Best Master Clock Algorithm. This is the case for Automotive
Profile where networks are mostly static and role for each device is
known in advance.
masterOnly and slaveOnly will be used to determine the roles for the
devices. Since masterOnly is a per-port config and slaveOnly is a global
config option, role assignment will be slightly odd in case of bridges.
If slaveOnly is set to 1, all the ports will be in slave roles except
for the ones where masterOnly is set to 1. These ports will assume the
master role.
Two new FSMs which will be used for master and slave roles for this
config option have also been added.
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
If set to 'true', this unconditionally sets the asCapable variable. The
usual checks will be applied to asCapable if it is set to 'auto'. The
default value is 'auto'.
This config option is needed by the Automotive Profile. The master will
be able to send out Sync Message as soon as the daemon is started.
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
This scenario will only be encountered when the clock transitions to the
slave state without knowing who the master is.
This will result in a segfault for BMCA with designated master and slave
states (to be added in upcoming patches).
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
If foreign clock is NULL, both the clocks are obviously not equal. So,
return 0 in that case.
The above condition (fc == NULL) is not currently encountered. It will
be encoutered in the next few patches which implement static roles for
master and slave.
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Remove > from beginning of lines specified in the *.conf sections in
order to allow a ptp4l-specific section (e.g. [unicast_master_table]) to
be included there.
After inserting the lines to the generated ptp4l.conf, switch back to
the [global] section.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Don't postpone processing of a timeout if it is equal to the current
time. This prevents an infinite loop with a simulated clock.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Currently the clockIdentity is generated from the mac address of the first
interface/port in config file. This patch add the possibility to set it in
config file.
The reason is if the stack is restarted with a different set of ports, it
may be circumstances when clockIdentity needs to be equal as before
restart even if the port setup is different.
Signed-off-by: Anders Selhammer <anders.selhammer@est.tech>
Add attribute maxStepsRemoved which is included in IEEE1588-2017 (v2.1)
It is an optional attribute which can decide if an Announce message is
considered in the operation of the BMCA or not.
Signed-off-by: Anders Selhammer <anders.selhammer@est.tech>
Add global option for the hardware time stamp setting.
The function could:
Normally set the filters as the PTP daemon require.
Check that the filters are proper but do not change them.
Full, set the RX filter to all and the TX filter as the PTP daemon require.
[ RC: added missing extern keyword and fixed indentation. ]
Signed-off-by: Erez Geva <erez.geva.ext@siemens.com>
Signed-off-by: Erez Geva <ErezGeva2@gmail.com>
The sub agent use net-snmp library and AgentX protocol for the
communication towards the snmp master agent.
snmpd.c should only include general setup needed for handling snmp.
Supported MIBs should be implemented in separate files.
Makefile will include snmpd if libsnmp is available during compilation.
configs/snmpd.conf should be placed in /etc/snmp/
Signed-off-by: Anders Selhammer <anders.selhammer@est.tech>
In port_management_fill_response() the TLV descriptor leaked when
not responding.
In port_open() the port would leak with the unsupported management clock
type.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Vedang Patel
Richard Cochran
Miroslav Lichvar
Hangbin Liu
David Mirabito via Linuxptp-devel
Anders Selhammer
Dimitrios Katsaros
Ethel Nilsson
Erez Geva