This config option will skip the source port identity verification in
the Sync and Follow_up messages. This option is needed when the announce
messages are disabled because the slave cannot know the identity of
master without announce messages.
This is required by Automotive Profile as part of skipping the Best
Master Clock Algorithm (BMCA).
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
This option will accomplish 2 things. On the master, it will stop the
announce messages being sent (by disabling FD_MANNO_TIMER timer). On
slave, it will not configure announce message timeouts (by disabling
FD_ANNOUNCE_TIMEOUT timer).
This config option is needed for the Automotive profile as part of
skipping the Best Master Clock Algorithm (BMCA).
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
This adds config option to specify static roles for master and slave
in the Best Master Clock Algorithm. This is the case for Automotive
Profile where networks are mostly static and role for each device is
known in advance.
masterOnly and slaveOnly will be used to determine the roles for the
devices. Since masterOnly is a per-port config and slaveOnly is a global
config option, role assignment will be slightly odd in case of bridges.
If slaveOnly is set to 1, all the ports will be in slave roles except
for the ones where masterOnly is set to 1. These ports will assume the
master role.
Two new FSMs which will be used for master and slave roles for this
config option have also been added.
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
If set to 'true', this unconditionally sets the asCapable variable. The
usual checks will be applied to asCapable if it is set to 'auto'. The
default value is 'auto'.
This config option is needed by the Automotive Profile. The master will
be able to send out Sync Message as soon as the daemon is started.
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Currently the clockIdentity is generated from the mac address of the first
interface/port in config file. This patch add the possibility to set it in
config file.
The reason is if the stack is restarted with a different set of ports, it
may be circumstances when clockIdentity needs to be equal as before
restart even if the port setup is different.
Signed-off-by: Anders Selhammer <anders.selhammer@est.tech>
Add attribute maxStepsRemoved which is included in IEEE1588-2017 (v2.1)
It is an optional attribute which can decide if an Announce message is
considered in the operation of the BMCA or not.
Signed-off-by: Anders Selhammer <anders.selhammer@est.tech>
Add global option for the hardware time stamp setting.
The function could:
Normally set the filters as the PTP daemon require.
Check that the filters are proper but do not change them.
Full, set the RX filter to all and the TX filter as the PTP daemon require.
[ RC: added missing extern keyword and fixed indentation. ]
Signed-off-by: Erez Geva <erez.geva.ext@siemens.com>
Signed-off-by: Erez Geva <ErezGeva2@gmail.com>
This patch adds configuration file support for a table of unicast
masters. Each table lives in its own section and has a unique,
positive numerical ID. Entries in the table are a pair of transport
type and protocol address.
Each port may specify a table id to be used for unicast negotiation.
Tables may not be shared between ports, but nothing prevents table
entries from appearing in more than table.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
According to 1588, PTP message loops are simply someone else's problem
with respect to transparent clocks. Since we are running the BMCA for
syntonization anyway, we might as well go ahead and implement the spanning
tree for PTP messages.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
This patch adds a new configuation option that enables transparent
clock mode. When TC mode is specified, the configured delay mechanism
must also match. The legacy behavior of upgrading a multi-port clock
from OC to BC is preserved.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
When masterOnly is true, the port always returns NULL when computing
its best foreign master. As a result, the port will never enter the
SLAVE state, and the clock will ignore Announce messages received on
that port.
This attribute is specifically called out in G.8275.1 and G.8275.2,
and it is implied by the "master only" mode G.8265.1. In addition,
this option will probably appear in the next revision of IEEE 1588.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Up until now, one step operation was controlled by a combination of
options, namely time_stamping=hardware with twoStepFlag=0. The
introduction of peer to peer one step makes the situation a bit more
complicated.
This patch adds support for setting the one step options directly by
using the "time_stamping" option. The "twoStepFlag" is adjusted
automatically if needed. The legacy behavior for Sync message one
step is preserved.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Up until now the transportSpecific field has been treated according to
802.1AS, namely as a field that must match exactly on receive.
However, 1588 mandates ignoring this field for some transports, and
there is equipment in the wild that does in fact set the reserved
bits.
This patch adds an option to ignore the field on receive completely.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reported-by: Petr Kulhavy <brain@jikos.cz>
This option allows the clock to be updated before the path delay is
measured in order to speed up the initial correction of the clock, e.g.
in domains using a very long logMinDelayReqInterval.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Now the ts label will be either the bond active slave or the interface
name, which is the exactly interface we need to get ts info.
When the link down/up or there is a fail over and ts_label changed, the
phc index may also changed. So we need to check get new ts info and check
clock_required_modes. We will set the link to LINK_DOWN by force if
the new ts_label's timestamp do not support required mode.
If all good, then we set phc index to new one. Also sync clock interval
after switch phc.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
When running multiple instances of ptp4l or phc2sys, it's difficult to
tell which log message belongs to which instance. Add new options to
ptp4l and phc2sys which can specify a tag for all messages printed to
the standard output or system log, so messages from different instances
can have different tags.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Currently UTC offset is defined as a constant - CURRENT_UTC_OFFSET, and if
a leap second is added, that constant is no longer valid. Ptp4l was
updated to read the UTC offset from configuration instead.
Signed-off-by: Viliam Lejcik <viliam.lejcik@kistler.com>
The recent change allowing every configuration option to appear on the
command line wrongly used bitwise AND to set a flag. This patch fixes
the bug by using the proper bitwise OR idiom.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Reported-by: Miroslav Lichvar <mlichvar@redhat.com>
Fixes: 4e8dbd8 ("ptp4l: Accept any configuration option as a command line argument.")
This patch provides a way to use the entire table of configuration options
as "long" command line switches.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
In the last years there are several media streaming standards
evolving that are relying on PTP. These standards make requirements
about the DSCP priority of PTP messages. This patch introduces two
new configuration options 'dscp_event' and 'dscp_general' to address
that issue and to be able to set the DSCP priority separately for
PTP event messages and PTP general messages.
Signed-off-by: Henry Jesuiter <henry.jesuiter@alcnetworx.de>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
There is no need to have a function to get this information as
we can easily obtain it when the interface is first created.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
The draft Enterprise Profile [1] specifies a hybrid E2E delay mechanism,
where the delay response message is sent "in kind". That is, if the
request is unicast, then the response is also unicast. Apparently this
scheme is already in widespread use in some industries. Also, it makes
sense, because those messages are of no interest to the other slaves in
the PTP network.
Because of the address work already in place, in turns out that adding
this mode is almost trivial. This patch introduces an "hybrid_e2e" option
that enabled the new mode.
1. https://datatracker.ietf.org/doc/draft-ietf-tictoc-ptp-enterprise-profile
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Now that all of the legacy, open coded configuration fields are gone,
we can follow a normal create/destroy pattern for the configuration.
This patch add the new method and converts the programs to use it.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Now that all of the legacy parsing code is gone, there remain two
identical parsing functions. This patch removes them both and places
the common code at the original call site.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
This patch rearranges the guts of the main parsing loop to keep it
more within the 80th column. The logic has not been changed.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Global default values will be static strings, but values from the
configuration file will be dynamic, so the code remembers whether or it
should free the string when cleaning up.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Vedang Patel
Anders Selhammer
Erez Geva
Richard Cochran
Rafaël Carré
Christoph Seifert
Miroslav Lichvar
Hangbin Liu
Viliam Lejcik
Richard Cochran
Jesuiter, Henry (ALC NetworX GmbH)