Use tmv_dbl() to obtain the floating point value passed to
stats_add_value() rather than relying on the existing implicit cast
from the result of tmv_to_nanoseconds().
Signed-off-by: Michael Brown <mbrown@fensystems.co.uk>
The code uses a local variable for program flow control in a silly way.
This patch simplifies the logic by using the common switch/case/default
pattern instead.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
This option allows the clock to be updated before the path delay is
measured in order to speed up the initial correction of the clock, e.g.
in domains using a very long logMinDelayReqInterval.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
The UDS port is not expected to be used by PTP clocks and forwarding of
management messages to the port can be limited to responses.
This prevents ptp4l from printing error messages when a management
request is received from a non-UDS port and the last client which used
the UDS port is no longer listening.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Now the ts label will be either the bond active slave or the interface
name, which is the exactly interface we need to get ts info.
When the link down/up or there is a fail over and ts_label changed, the
phc index may also changed. So we need to check get new ts info and check
clock_required_modes. We will set the link to LINK_DOWN by force if
the new ts_label's timestamp do not support required mode.
If all good, then we set phc index to new one. Also sync clock interval
after switch phc.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Separate required_modes setting from clock_create so we can obtain the
required time stamping flags from other place.
Add enum timestamping in struct clock to store the time stamping mode.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Now that we test the UTC flags in clock_update_slave(), the similar
code in clock_utc_correct() is redundant.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
When acting as a slave, we accept the foreign master's advertised
TAI-UTC offset for as long as that master is present. However, when
the master disappears, we fall back to the initial offset value. As a
result of this behavior, when starting with an out of date initial
offset, losing a foreign master causes a sudden UTC offset error (in
phc2sys for example) in the range of whole seconds.
This patch fixes the issue by remembering the UTC offset when assuming
the slave role.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
The clock code uses two different variables to store the TAI-UTC
offset. One variable represents the compile time, configuration file,
or command line initial UTC offset, while the other is used when
taking on the GM role and is settable at run time. However, making
this distinction makes no sense. This patch simplifies and clarifies
the code by using a single variable for the offset.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
With rtnl socket we can track link status per port(except UDS port).
We can make sure we get the correct interface and latest status with function
port_link_status().
At the same time we need to set clock sde after link down. But we return
EV_FAULT_DETECTED in port_event(), which will not set clock sde. So we need
to set it in port_link_status().
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
The calls to snprintf() to format /dev/phc%d use the wrong pattern.
That function always properly terminates the string with null.
However, the code passes a hard coded length of 31 to static arrays of
length 32. While this is not a bug, there are two issues here.
First, any (improbable) future increase in the array lengths would
have to also remember to fix up the snprintf() call site as well.
Secondly, the pattern of using buf[N] and then length=N-1 is
appropriate for strncpy(), but is useless for snprintf().
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reported-by: Petr Kulhavy <brain@jikos.cz>
Having one fewer port may affect the result of the BMCA. This patch
changes the main loop so that a link down event also causes a state
decision event.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reported-by: Henry Jesuiter <Henry.Jesuiter@alcnetworx.de>
This global function used to return an error code, but now it always
returns zero. This patch converts the function signature to return void
and simplifies the main clock loop by removing the useless test.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Currently UTC offset is defined as a constant - CURRENT_UTC_OFFSET, and if
a leap second is added, that constant is no longer valid. Ptp4l was
updated to read the UTC offset from configuration instead.
Signed-off-by: Viliam Lejcik <viliam.lejcik@kistler.com>
Poll for link up/down events. When a link goes down, the port becomes
faulty until the link goes up again. We keep the fault timer from the
existing fault detection, but a downed link prevents clear the fault.
The new state machine is depicted in this ascii art diagram:
+--------+ Fault +---------+
| |------------>| |
| UP | | FAULT |
| |<------------| |
+--------+ Timeout +---------+
A | /
| | /
Link-Up | | Link-Down /
| | /
| V /
+--------+ / Link-Down
| | /
| DOWN |<--------/
| |
+--------+
If the fault timer occurs in the DOWN state, we simply ignore it.
After all, without the link the port is useless.
There is one case where the new code changes the existing behavior.
If the link quickly does down and then up again while another fault
(and its timer) are active, then we will enter the UP state without
waiting for the fault timer expiration. However, this behavior is
acceptable because when a link goes up, you are starting with a clean
slate.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
We use a hash table to remember the mapping. Since our existing hash
table is a simply string hash, we convert the integer index into a decimal
string. Although hashing integers in this way is sub-optimal, the table
will not be used in a performance critical path.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
The time stamping setup code needlessly queries the configuration data
base over and over, rather than simply using the local variable
already assigned. This patch replaces the extraneous config_get_int()
calls with the local variable.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
We activate on-step mode based on the "time_stamping" and
"twoStepFlag" configuration options. If twoStepFlag is false and HW
time stamping is enabled, we upgrade the time stamping mode variable
to one-step.
The code that tests the options and sets the one-step mode moved from
ptp4l.c into clock.c in commit 9b27664c ("clock: simplify the create
method."). However, that commit inadvertently moved the test after
the place where the time stamping mode is latched in a local variable.
As a result, one-step mode is not activated when configured.
This patch fixes the issue by keeping the local time stamping mode
variable up to date during the one-step test.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
During the configuration rework, the announce span was wrongly converted
into a hard coded macro. In addition, the announceReceiptTimeout option
inadvertently became non-zero for the UDS port. As a result, the UDS port
sets a useless announce message timer, causing the code to close and reopen
the UDS port every few seconds.
This bug has an interesting history. It was first reported and fixed in
commit f36af8e0 ("uds: disable the accidentally enabled announce timer.").
That very fix was wrongly removed in commit 54f45063 ("port: change
'announce_span' into a macro."). Because of various code changes, this
bad commit cannot be simply reverted now.
This patch re-introduces the 'announce_span' variable and clears both it
and 'announceReceiptTimeout' for the UDS port, effectively disabling the
announce message timer.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
The code that determines the index of the PHC device is useful to all
kinds of clock devices.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
This function will allow the TC code to iterate over the ports without
calling into the clock logic.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
The port code is not interested in the number of ports but rather the
clock type. Since the polymorphic clock object will be able to report
its own type, this patch changes the clock interface accordingly.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
There is no need for the 'ifaces' parameter since the list of network
interfaces is already present in the configuration.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
With the new configuration API, there is no need to pass the default data
set. Instead, the clock code can read the configuration directly. This
patch simplifies the clock create method by removing the 'dds' parameter
and moving the code that initialized the data set into the clock module.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
The new configuration code inadvertently causes the UDS port to use P2P
messaging when P2P is set as a global option. This results in a never
ending series of "missing timestamp" error messages from the UDS port as
it vainly tries to send peer delay requests.
This patch fixes the bug by changing the UDS delay mechanism back to zero
as it was before. This is the appropriate setting for the UDS port,
because it never leaves the listening state and thus never sends an E2E
delay request.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
This function allows the ports to read configuration variables without
changing the port method signatures.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
This will help us to simplify the passing of parameters between the main
program. clock, and ports.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
This patch adds support for changing the priority1 and priority2
elements of the "default data set" at run time.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Add weight parameter to the sample function. Samples with smaller weight
are less reliable, they can be ignored by the servo or the adjustments
of the clock can be smaller.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Add new time stamp processing modes to return raw delay and offset based
on the raw delay instead of the long-term filtered delay, and to return
also a weight of the sample. The weight is set to the ratio between the
two delays. This gives smaller weight to samples where the sync and/or
delay messages were delayed significantly in the network and possibly
include a large error.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Introduce a time stamp processor for offset/delay calculations and use
it in the clock and port modules.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Convert time stamps to tmv_t and apply all corrections before passing
them to clock/port functions to reduce the number of parameters.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
When switching clock devices in JBOD mode, we need to be able to reset the
servo. The existing servo_reset() function will not serve us well, because
in this case we also need to seed the existing frequency offset and limit.
This patch adds a new method that simply starts the servo from scratch.
In the unlikely event of a resource allocation failure, the method will
simply continue to use the previous device, which is better than nothing
and certainly preferable to bailing out the program.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
When adding a new port, put it at the end of the list instead of head.
This restores the order of received management messages as was before
commit 08575133.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
For the ports to be truly created and removed dynamically, the last used
port number has to be remembered by the clock and used for port creation.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
There's no need to regenerate pollfd multiple times during batches of port
operations (like creating of the clock). Just be lazy and regenerate it only
once it's needed.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Remove the limit of MAX_PORTS ports (default 8) and keep the ports in
a linked list. This allows ptp4l to be used on large machines and in the
future, it will allow dynamic adding and removing of ports while ptp4l is
running.
For this to work, pollfd needs to be dynamically allocated. Changed pollfd
handling from clock_install_fda/clock_remove_fda to notification
(clock_fda_changed), where the clock will rebuild pollfd by querying all its
ports.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
The uds port is handled specially in almost all cases, it doesn't behave
like the rest of ports in the port array. Make it a standalone member of
struct clock.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
The fault timer file descriptor is a per port item, put it inside struct
port where other per port file descriptors are kept.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Introduce a new function to inform the servo about upcoming leap second.
This is used when the kernel leap is disabled to allow the servo to
handle better the sudden 1 second step in the offset when the leap
second is inserted or deleted.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
When synchronizing the system clock and the PTP UTC offset is valid and
traceable, set the TAI offset of the clock to have correct CLOCK_TAI
(which is implemented in the kernel as CLOCK_REALTIME + TAI offset).
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Split management message creation to more fine-grained functions to allow
notification messages to be created.
The new clock_management_fill_response is called from
clock_management_get_response (so the function behaves exactly the same as
before this patch) and from a new clock_notify_event function. The
difference is clock_management_get_response uses the request message to
construct the reply message, while clock_notify_event constructs the reply
message based on the notification id.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Add expiration time to subscriptions; they need to be renewed before they
expiry. This way, the subscription automatically times out when phc2sys is
killed.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
This puts groundwork for event subscription and notification. The individual
events are added by subsequent patches.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
The task of preparing the message for transmission and sending it appears
at many places. Unify them into a new function.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Currently, it is assumed that the management TLV data of management COMMAND
messages is always empty. This is not true for the INITIALIZE command and
also for a custom command we'll be introducing.
Move the check to msg_post_recv and let it check only the TLVs defined by
the standard.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
With the new linreg servo the frequency offset and time offset are
controlled separately. The ratio between master's frequency and the
current frequency of the local clock is known and can be used when
calculating delay or peer delay to improve their accuracy.
This greatly improves the stability of the delay when the servo is
correcting a large offset.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Setting GRANDMASTER_SETTINGS_NP is allowed only from UDS, but
PORT_DATA_SET can be set from any port. Move the port check to
clock_manage(), so all clock and port SET actions are restricted
to the UDS port.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
This fixes cumulativeScaledRateOffset reported in TIME_STATUS_NP before
the rate ratio is updated from port.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
The 'struct interface' for the UDS port is allocated on the stack, and
when this gets passed to port_open, the port instance takes a pointer to
the string in the 'name' field. Currently this is harmless for the UDS
port, but it is not good form. This patch fixes the issue by making the
interface part of the clock instance.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reported-by: Miroslav Lichvar <mlichvar@redhat.com>
Negative path delay measurements are expected with E2E, the user doesn't
need to know when that happens.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Although it does not need to, the UDS port tries to allocate a filter,
just as any normal port would. Since the given length is zero, the
filter tries to allocate storage of size zero. When running with
uClibc, calloc(1, 0) returns NULL, but glibc is apparently returning
"a unique pointer value that can later be successfully passed to
free()." Both behaviors are allowed (see MALLOC(3)).
This patch works around the issue by letting the UDS port have a
filter of length one.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
This patch lets the clock release allocated memory when shutting down. The
main benefit is just to exhibit good form and to make valgrind happier.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Add new options delay_filter and delay_filter_length to select the
filter and its length. They set both the clock delay filter and the port
peer delay filter. The default is now moving median with 10 samples.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Similarly to the servo interface, allow multiple filters to be
used for delay filtering. Convert mave to the new interface.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Include also nanoseconds from the current time in the srandom() call.
This should significantly decrease the chance of two machines using the
same random sequence.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Check the sanity of the synchronized clock by comparing its uncorrected
frequency with the system monotonic clock. When the measured frequency
offset is larger than the value of the sanity_freq_limit option (20% by
default), a warning message will be printed and the servo will be reset.
Setting the option to zero disables the check.
This is useful to detect when the clock is broken or adjusted by another
program.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
When a new master is selected, drop the old sync time stamp to prevent
calculating invalid delay in case delay_resp will be received before
first sync from the new master.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
This patch changes the macro for the server socket address into a global
variable so that a subsequent patch can provide a way to set the variable.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
When the socket couldn't be opened (e.g. in clknetsim), the file
descriptor is invalid and shouldn't be used for sending.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Add 1 to port numbers printed in the log messages to make them
consistent with messages from port.c. The port number 0 is the UDS port,
which is last in the clock->port array.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
This patch cleans up the BMC logic to allow assuming the GM role when no
other clocks are found in the network. By allowing the "best" to be NULL,
we can let the BMC to naturally pick the local clock as GM. As an added
bonus, this also get rid of the hacky check for a lost master.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
This patch adds a new servo method to let the algorithm know about the
master clock's reported sync message interval. This information can be
used by the servo to adapt its synchronization parameters.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Management messages can cause a change in the clock quality. If this
happens, then it is time to run the Best Master Clock algorithm again.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Michael Brown
Richard Cochran
Miroslav Lichvar
Hangbin Liu
Viliam Lejcik
Jiri Benc