This conversion is not straightforward due to the fact that these options
can take a value of "ASAP" or a number. We check for the special ASAP
case in a helper function and leave the numbers to the generic code.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Add new time stamp processing modes to return raw delay and offset based
on the raw delay instead of the long-term filtered delay, and to return
also a weight of the sample. The weight is set to the ratio between the
two delays. This gives smaller weight to samples where the sync and/or
delay messages were delayed significantly in the network and possibly
include a large error.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Introduce a time stamp processor for offset/delay calculations and use
it in the clock and port modules.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Convert time stamps to tmv_t and apply all corrections before passing
them to clock/port functions to reduce the number of parameters.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
If the user has configured the appropriate option, then simply warn
about the clock device mismatch, and then go on in "JBOD" mode.
Whenever the port enters the uncalibrated state, it tells the clock
to switch to the new PHC device.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Commit ea7a7882 removed the calls to transport_peer(), inadvertently
substituting them with transport_send(), resulting in PDelay messages
being sent with an incorrect destination address.
This patch fixes the issue by introducing peer_prepare_and_send(),
analogous to the port_prepare_and_send() function.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jiri Benc <jbenc@redhat.com>
Remove the limit of MAX_PORTS ports (default 8) and keep the ports in
a linked list. This allows ptp4l to be used on large machines and in the
future, it will allow dynamic adding and removing of ports while ptp4l is
running.
For this to work, pollfd needs to be dynamically allocated. Changed pollfd
handling from clock_install_fda/clock_remove_fda to notification
(clock_fda_changed), where the clock will rebuild pollfd by querying all its
ports.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
The fault timer file descriptor is a per port item, put it inside struct
port where other per port file descriptors are kept.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Split management message creation to more fine-grained functions to allow
notification messages to be created.
The new clock_management_fill_response is called from
clock_management_get_response (so the function behaves exactly the same as
before this patch) and from a new clock_notify_event function. The
difference is clock_management_get_response uses the request message to
construct the reply message, while clock_notify_event constructs the reply
message based on the notification id.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Split management message creation to more fine-grained functions to allow
notification messages to be created.
The new port_management_fill_response is called from
port_management_get_response (so the function behaves exactly the same
as before this patch) and from a new port_notify_event function. The
difference is port_management_get_response uses the request message to
construct the reply message, while port_notify_event constructs the
reply message based on the notification id.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
The callers of those functions are all using ptp_message. As we're going to
return more information (the address), let those functions just fill in the
ptp_message fields directly.
Some minor reshuffling needed to prevent circular header dependencies.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
The task of preparing the message for transmission and sending it appears
at many places. Unify them into a new function.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
With the new linreg servo the frequency offset and time offset are
controlled separately. The ratio between master's frequency and the
current frequency of the local clock is known and can be used when
calculating delay or peer delay to improve their accuracy.
This greatly improves the stability of the delay when the servo is
correcting a large offset.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
When peer delay is < min_neighbor_prop_delay the port is flagged
as non 802.1AS capable. min_neighbor_prop_delay defaults to -20ms.
Signed-off-by: Delio Brignoli <dbrignoli@audioscience.com>
Previouly the peer delay was not taking into account the
frequency offset between the local clock and the peer's clock.
Reset neighborRateRatio to 1.0 in port_nrate_initialize().
Signed-off-by: Delio Brignoli <dbrignoli@audioscience.com>
Commit e425da2f inadvertently enabled the announce timer on the UDS port,
causing it to continually reopen the socket when in slave mode. This patch
fixes the issue by passing zero in the 'span' field of the new function,
set_tmo_random, which disables the timer again.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reported-by: Rohrer Hansjoerg <hj.rohrer@mobatime.com>
According to 802.1AS, ports are always expected to transmit announce
messages, even if they never want to become the grand master. Instead
of using a slave only BMC state machine as in 1588, 802.1AS offers a
"grand master capable" flag which allows clocks to not send sync
messages.
This patch keeps a port from transmitting sync (but not announce)
messages when there is no other master.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
[ RC: the point is that a port may not be considered capable until
enough messages to compute the ratio have been received. ]
Signed-off-by: Delio Brignoli <dbrignoli@audioscience.com>
Reviewed-by: Richard Cochran <richardcochran@gmail.com>
Sync rx timeout should be set only after receiving the first sync, see
section 10.2.7, figure 10-4 PortSyncSyncReceive state machine in 802.1AS
Signed-off-by: Delio Brignoli <dbrignoli@audioscience.com>
Add new options delay_filter and delay_filter_length to select the
filter and its length. They set both the clock delay filter and the port
peer delay filter. The default is now moving median with 10 samples.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Similarly to the servo interface, allow multiple filters to be
used for delay filtering. Convert mave to the new interface.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Instead of maintaining a table of precalculated values, use the
newly added set_tmo_random() function to set the delay request timeout.
It saves some memory and improves the timeout granularity, but has a
higher computational cost. It follows the requirements from section
9.5.11.2 of the spec.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
According to 9.2.6.11 of the spec the ANNOUNCE_RECEIPT_TIMEOUT_EXPIRES
timeout in addition to announceReceiptTimeoutInterval includes a random
number up to one announceInterval.
Add a new function for setting random timeout and use it in
port_set_announce_tmo().
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Check the sanity of the synchronized clock by comparing its uncorrected
frequency with the system monotonic clock. When the measured frequency
offset is larger than the value of the sanity_freq_limit option (20% by
default), a warning message will be printed and the servo will be reset.
Setting the option to zero disables the check.
This is useful to detect when the clock is broken or adjusted by another
program.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
When a new master appears, it will start to respond to our delay_req
messages. Make sure we process only responses from our current master
before switching to the new master.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
When ptp4l was configured to use the auto delay mechanism and the first
pdelay request was not received in the slave or uncalibrated state, it
would not make any pdelay requests itself, because there was no delay
timer running.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Because of packet reordering that can occur in the network, in the
hardware, or in the networking stack, a follow up message can appear
to arrive in the application before the matching sync message. As this
is a normal occurrence, and the sequenceID message field ensures
proper matching, the ptp4l program accepts out of order packets.
This patch adds an additional check using the software time stamps
from the networking stack to verify that the sync message did arrive
first. This check is only useful if the sequence IDs generated by
the master might possibly be incorrect.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
This patch lets a port send the first announce message one millisecond
after the port state transition, rather than waiting one announce interval.
This change is needed because it is desirable to reconfigure the time
network without delay, especially in P2P mode.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
This patch adds a new timer for use in 802.1AS-2011 applications. When
running as a slave in gPTP mode, the program must monitor both announce
and sync messages from the master. If either one goes missing, then we
trigger a BMC election. The sync timeout is actually reset by a valid
sync/follow up pair of messages.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
This patch renames the per-port timer in order to make room in the
namespace for a timer that detects a sync message input timeout.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
The closing and reopening of the transport when in slave only mode is not
necessary if the port is using the peer delay mechanism. In that case, the
port will discover the network error by transmitting a peer delay request.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Delio Brignoli <dbrignoli@audioscience.com>
Ken Ichikawa has identified a situation in which a sync message can be
wrongly associated with a follow up after the sequence counter wraps
around.
Port is LISTENING
Sync (seqId 0) : ignored
Fup (seqId 0) : ignored
Sync (seqId 1) : ignored
Port becomes UNCALIBRATED here
Fup (seqId 1) : cached!
Sync (seqId 2) : cached
Fup (seqId 2) : match
Sync (seqId 3) : cached
Fup (seqId 3) : match
...
Sync (seqId 65535) : cached
Fup (seqId 65535) : match
Sync (seqId 0) : cached
Fup (seqId 0) : match
Sync (seqId 1) : match with old Fup!!
Fup (seqId 1) : cached!
Sync (seqId 2) : cached
Fup (seqId 2) : match
Actually, I experienced 65500 secs offset every about 65500 secs.
I'm thinking this is the cause.
This patch fixes the issue by changing the port code to remember one
sync or one follow up, never both. The previous ad hoc logic has been
replaced with a small state machine that handles the messages in the
proper order.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reported-by: Ken ICHIKAWA <ichikawa.ken@jp.fujitsu.com>
This patch fixes a bug with time mysteriously jumping back and forth:
ptp4l[930.687]: port 1: UNCALIBRATED to SLAVE on MASTER_CLOCK_SELECTED
ptp4l[931.687]: master offset 17 s2 freq +33014 path delay 2728
ptp4l[932.687]: master offset -74 s2 freq +32928 path delay 2734
ptp4l[933.687]: master offset 2 s2 freq +32982 path delay 2734
ptp4l[934.687]: master offset -3 s2 freq +32977 path delay 2728
ptp4l[935.687]: master offset 17 s2 freq +32996 path delay 2729
ptp4l[936.687]: master offset -10 s2 freq +32974 path delay 2729
ptp4l[937.687]: master offset 35 s2 freq +33016 path delay 2727
ptp4l[938.686]: master offset 60001851388 s2 freq +62499999 path delay 2728
ptp4l[939.687]: master offset -62464938 s2 freq -62431946 path delay 2728
The last follow up message arriving out of order is cached. Before the state
machine changes to UNCALIBRATED, all sync and follow up messages are discarded.
If we get into that state between a sync and follow up message, the latter is
cached. When there's no real roerdering happening, it's kept cached forever.
When we restart the master, it starts numbering the messages from zero again.
The initial synchronization doesn't take always the same amount of time, so it
can happen that we get into UNCALIBRATED a little bit faster than before,
managing to get the sync message with the sequenceId that we missed last time.
As it has the same sequenceId as the cached (old) follow up message, it's
incorrectly assumed those two belong together.
Flush the cache when changing to UNCALIBRATED. Also, do similar thing for other
cached packets.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Management messages can cause a change in the clock quality. If this
happens, then it is time to run the Best Master Clock algorithm again.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Whenever a port enters the passive state, it should act like a slaved
port in one respect. Incoming announce messages from the grand master
are supposed to reset the announce timer. This patch fixes the port
logic to properly maintain the passive state.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reported-by: Rohrer Hansjoerg <hj.rohrer@mobatime.com>
When there is a peer speaking PTPv1 in the network we want to silently ignore
the packets instead of flooding system log with error messages. At the same
time we still want to report malformed packets. For that we reuse standard
error numbers and do more fine-grained error reporting in packet processing
routines.
Signed-off-by: Libor Pechacek <lpechacek@suse.cz>
Handle reception of >=3 sequential multiple pdelay responses from
distinct peers as a fault of type FT_BAD_PEER_NETWORK.
Signed-off-by: Delio Brignoli <dbrignoli@audioscience.com>
This patch also changes port_capable() to reset the port's nrate every time asCapable changes
from true to false.
Signed-off-by: Delio Brignoli <dbrignoli@audioscience.com>
If messages are not freed, it is possible (with purposely crafted traffic) to trigger
a peer delay calculation which will use message's data from the previous round.
Signed-off-by: Delio Brignoli <dbrignoli@audioscience.com>
When a port makes a transition from one state to another, it resets all of
the message timers. While this is the correct behavior for E2E mode, the
P2P mode requires sending peer delay requests most of the time.
Even though all the other timer logic is identical, still making an
exception for P2P mode would make the code even harder to follow. So this
patch introduces two nearly identical helper functions to handle timer
reprogramming during a state transition.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Now that there are clock/port_management_set functions, the IDs that
GETs are handled for, like DEFUALT_DATA_SET, still need to be in the
case for sending NOT_SUPPORTED errors.
Signed-off-by: Geoff Salmon <gsalmon@se-instruments.com>
Adds port_management_send_error and clock_management_send_error to
avoid repeatedly checking the result of port_managment_send_error and
calling pr_err if it failed. Future patches send more mgmt errors so
this will avoid repeated code.
Signed-off-by: Geoff Salmon <gsalmon@se-instruments.com>
There really is no such state, but there probably should have been one.
In any case, we do have one just to make the code simpler, but this should
not appear in the management responses. This patch fixes the issue by
covering over our tracks before sending a response.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
If the port resets itself after detecting a fault, then the polling events
for that port are no longer valid. This patch fixes a latent bug that
would appear if a fault and another event were to happen simultaneously.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
A timeout of 15 seconds is not always acceptable, make it configurable.
By popular consensus, instead of using a linear number of seconds, use
the 2^N format for the time interval, just like the other intervals in
the PTP data sets. In addition to numeric values, let the configuration
file support 'ASAP' to have the fault reset immediately.
[RC - moved the handling of special case tmo=0 and added a break out
of the fd event loop in case the fds have been closed.
- changed the linear seconds option to log second instead.
- changed the commit message to reflect the final version. ]
Signed-off-by: Delio Brignoli <dbrignoli@audioscience.com>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Richard Cochran
Miroslav Lichvar
Jiri Benc
Delio Brignoli
Libor Pechacek
Geoff Salmon