The closing and reopening of the transport when in slave only mode is not
necessary if the port is using the peer delay mechanism. In that case, the
port will discover the network error by transmitting a peer delay request.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Delio Brignoli <dbrignoli@audioscience.com>
Add 1 to port numbers printed in the log messages to make them
consistent with messages from port.c. The port number 0 is the UDS port,
which is last in the clock->port array.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Ken Ichikawa has identified a situation in which a sync message can be
wrongly associated with a follow up after the sequence counter wraps
around.
Port is LISTENING
Sync (seqId 0) : ignored
Fup (seqId 0) : ignored
Sync (seqId 1) : ignored
Port becomes UNCALIBRATED here
Fup (seqId 1) : cached!
Sync (seqId 2) : cached
Fup (seqId 2) : match
Sync (seqId 3) : cached
Fup (seqId 3) : match
...
Sync (seqId 65535) : cached
Fup (seqId 65535) : match
Sync (seqId 0) : cached
Fup (seqId 0) : match
Sync (seqId 1) : match with old Fup!!
Fup (seqId 1) : cached!
Sync (seqId 2) : cached
Fup (seqId 2) : match
Actually, I experienced 65500 secs offset every about 65500 secs.
I'm thinking this is the cause.
This patch fixes the issue by changing the port code to remember one
sync or one follow up, never both. The previous ad hoc logic has been
replaced with a small state machine that handles the messages in the
proper order.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reported-by: Ken ICHIKAWA <ichikawa.ken@jp.fujitsu.com>
This patch adds a new pmc command called "target" that lets the user
address a particular clock and port. Previously all management requests
were sent to the wild card address.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
This patch replaces the hard coded wild card target port identity with
a variable initially set to the wild card value. The intent is to allow
the caller to set specific targets.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
This patch makes the original behavior of sending the
TLV values for GET actions with a length of zero.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
This commit makes the GET messages have data bodies, just like the erratum
says to. It really doesn't make sense, but have to do it anyhow. We also
introduce a variable that will enable the legacy behavior of sending
empty bodies.
http://standards.ieee.org/findstds/interps/1588-2008.html
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
This patch lets the TLV length field of GET messages come from a
function. For now, the function still results in a length of two,
but the intent is to allow different values later.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
This patch adds proper byte order processing for the target port
identity field of management messages. This bug was not previously
noticed due to the fact that our client had always set this field
to the wild card port number of 0xffff.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
This patch fixes a bug with time mysteriously jumping back and forth:
ptp4l[930.687]: port 1: UNCALIBRATED to SLAVE on MASTER_CLOCK_SELECTED
ptp4l[931.687]: master offset 17 s2 freq +33014 path delay 2728
ptp4l[932.687]: master offset -74 s2 freq +32928 path delay 2734
ptp4l[933.687]: master offset 2 s2 freq +32982 path delay 2734
ptp4l[934.687]: master offset -3 s2 freq +32977 path delay 2728
ptp4l[935.687]: master offset 17 s2 freq +32996 path delay 2729
ptp4l[936.687]: master offset -10 s2 freq +32974 path delay 2729
ptp4l[937.687]: master offset 35 s2 freq +33016 path delay 2727
ptp4l[938.686]: master offset 60001851388 s2 freq +62499999 path delay 2728
ptp4l[939.687]: master offset -62464938 s2 freq -62431946 path delay 2728
The last follow up message arriving out of order is cached. Before the state
machine changes to UNCALIBRATED, all sync and follow up messages are discarded.
If we get into that state between a sync and follow up message, the latter is
cached. When there's no real roerdering happening, it's kept cached forever.
When we restart the master, it starts numbering the messages from zero again.
The initial synchronization doesn't take always the same amount of time, so it
can happen that we get into UNCALIBRATED a little bit faster than before,
managing to get the sync message with the sequenceId that we missed last time.
As it has the same sequenceId as the cached (old) follow up message, it's
incorrectly assumed those two belong together.
Flush the cache when changing to UNCALIBRATED. Also, do similar thing for other
cached packets.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
This patch cleans up the BMC logic to allow assuming the GM role when no
other clocks are found in the network. By allowing the "best" to be NULL,
we can let the BMC to naturally pick the local clock as GM. As an added
bonus, this also get rid of the hacky check for a lost master.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Instead of using fixed constants, set them by the following formula from
the current sync to allow good performance of the servo even when the
sync interval changes in runtime and to avoid instability.
kp = min(kp_scale * sync^kp_exponent, kp_norm_max / sync)
ki = min(ki_scale * sync^ki_exponent, ki_norm_max / sync)
The scale, exponent and norm_max constants are configurable. The
defaults are chosen so there is no change to the previous default
constants of the servo with one second sync interval. The automatic
adjustment can be disabled by setting the pi_proportional_const and
pi_integral_const options to a non-zero value, but stability of the
servo is always enforced.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
A slow servo (with smaller constants and lower sync rate) needs a
longer, better frequency estimation, but a higher sync rate hardly
needs any estimation at all, since it learns the frequency right away
in any case.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
This patch adds a new servo method to let the algorithm know about the
master clock's reported sync message interval. This information can be
used by the servo to adapt its synchronization parameters.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Management messages can cause a change in the clock quality. If this
happens, then it is time to run the Best Master Clock algorithm again.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
This patch also replaces the hard coded logic for the UTC offset and the
time property flags with clock variables. This new clock state will be
used for adjusting the grand master attributes at run time.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
When running as grand master, the attributes of the local clock are not
known by the ptp4l program. Since these attributes may change over time,
for example when losing signal from GPS satellites, we need to have a
way to provide updated information at run time. This patch provides a
new TLV intended for local IPC that contains the required settings.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
While the userDescription field is implemented in the code, the same
option is not present in the sample configuration file. This patch
fixes the issue by adding the option with an empty default value.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reported-by: Rohrer Hansjoerg <hj.rohrer@mobatime.com>
Whenever a port enters the passive state, it should act like a slaved
port in one respect. Incoming announce messages from the grand master
are supposed to reset the announce timer. This patch fixes the port
logic to properly maintain the passive state.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reported-by: Rohrer Hansjoerg <hj.rohrer@mobatime.com>
This patch removes a redundant initialization of the kernel_leap clock
variable. The field is already set in clock_create a few lines earlier.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
You'd probably expect the body of GET messages to be empty, but
interpretation #29 in
http://standards.ieee.org/findstds/interps/1588-2008.html implies
otherwise. With this change, ptp4l will respond to GETs containing
either an empty dataField or a dataField whose length matches the
managementId. If present, the contents of the dataField are ignored.
Signed-off-by: Geoff Salmon <gsalmon@se-instruments.com>
This patch adds support for using the configured_pi_f_offset servo option to ptp4l.
If "pi_f_offset_const 0.0" is specified in the config file, stepping on the first
update is prevented. If any other positive value is specified, stepping on the
first update occurs when the offset is larger than the specified value.
change since v1
- add the new option to default.cfg and gPTP.cfg
Signed-off-by: Ken ICHIKAWA <ichikawa.ken@jp.fujitsu.com>
Current pi servo steps clock without any condition on start.
This patch adds a new servo option "configured_pi_f_offset". The option is similar
to configured_pi_offset but only affects in the first clock update. Therefore,
if this option is set as 0.0, we can prevent clock step on start.
The new servo option can be specified from phc2sys by using -F option.
This feature is usefull when we need to restart phc2sys without system
clock jump. Restarting phc2sys is needed to change its configuration.
changes since v2:
- manual page fix.
- also apply max_offset along with max_f_offset in servo step1.
- add a variable to check if first update is done.
changes since v1:(http://sourceforge.net/mailarchive/message.php?msg_id=31039874)
- remake as a new servo option.
Signed-off-by: Ken ICHIKAWA <ichikawa.ken@jp.fujitsu.com>
Options without parameters are now grouped together at the beginning of line
for better legibility.
Signed-off-by: Libor Pechacek <lpechacek@suse.cz>
Cc: Miroslav Lichvar <mlichvar@redhat.com>
The get_ranged_ and get_arg_ declarations and definitions are just a wee
bit much too long. This patch breaks the overly long lines into two.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Ever since upgrading to Debian 7.0, building linuxptp results in an
annoying error message. This is due to the fact that the directory
/usr/include/bits is no longer present, but our makefile expects it
to exist. This patch fixes the issue by telling grep not to complain
about missing files.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
phc_open() can open any device and return clkid even if the device is not phc
for example /dev/kvm and so on.
As a result, phc2sys keeps running with reading bogus clock as below:
# phc2sys -s /dev/kvm -O 0 -q -m
phc2sys[687019.699]: failed to read clock: Invalid argument
phc2sys[687020.699]: failed to read clock: Invalid argument
phc2sys[687021.699]: failed to read clock: Invalid argument
phc2sys[687022.699]: failed to read clock: Invalid argument
...
This patch fixes that problem.
Signed-off-by: Ken ICHIKAWA <ichikawa.ken@jp.fujitsu.com>
Richard Cochran
Delio Brignoli
Miroslav Lichvar
Andy Lutomirski
Jiri Benc
Geoff Salmon
Dale P. Smith
Ken ICHIKAWA
Libor Pechacek