This conversion is not straightforward due to the fact that these options
can take a value of "ASAP" or a number. We check for the special ASAP
case in a helper function and leave the numbers to the generic code.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Add new time stamp processing modes to return raw delay and offset based
on the raw delay instead of the long-term filtered delay, and to return
also a weight of the sample. The weight is set to the ratio between the
two delays. This gives smaller weight to samples where the sync and/or
delay messages were delayed significantly in the network and possibly
include a large error.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Introduce a time stamp processor for offset/delay calculations and use
it in the clock and port modules.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Convert time stamps to tmv_t and apply all corrections before passing
them to clock/port functions to reduce the number of parameters.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
If the user has configured the appropriate option, then simply warn
about the clock device mismatch, and then go on in "JBOD" mode.
Whenever the port enters the uncalibrated state, it tells the clock
to switch to the new PHC device.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Commit ea7a7882 removed the calls to transport_peer(), inadvertently
substituting them with transport_send(), resulting in PDelay messages
being sent with an incorrect destination address.
This patch fixes the issue by introducing peer_prepare_and_send(),
analogous to the port_prepare_and_send() function.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jiri Benc <jbenc@redhat.com>
Remove the limit of MAX_PORTS ports (default 8) and keep the ports in
a linked list. This allows ptp4l to be used on large machines and in the
future, it will allow dynamic adding and removing of ports while ptp4l is
running.
For this to work, pollfd needs to be dynamically allocated. Changed pollfd
handling from clock_install_fda/clock_remove_fda to notification
(clock_fda_changed), where the clock will rebuild pollfd by querying all its
ports.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
The fault timer file descriptor is a per port item, put it inside struct
port where other per port file descriptors are kept.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Split management message creation to more fine-grained functions to allow
notification messages to be created.
The new clock_management_fill_response is called from
clock_management_get_response (so the function behaves exactly the same as
before this patch) and from a new clock_notify_event function. The
difference is clock_management_get_response uses the request message to
construct the reply message, while clock_notify_event constructs the reply
message based on the notification id.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Split management message creation to more fine-grained functions to allow
notification messages to be created.
The new port_management_fill_response is called from
port_management_get_response (so the function behaves exactly the same
as before this patch) and from a new port_notify_event function. The
difference is port_management_get_response uses the request message to
construct the reply message, while port_notify_event constructs the
reply message based on the notification id.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
The callers of those functions are all using ptp_message. As we're going to
return more information (the address), let those functions just fill in the
ptp_message fields directly.
Some minor reshuffling needed to prevent circular header dependencies.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
The task of preparing the message for transmission and sending it appears
at many places. Unify them into a new function.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
With the new linreg servo the frequency offset and time offset are
controlled separately. The ratio between master's frequency and the
current frequency of the local clock is known and can be used when
calculating delay or peer delay to improve their accuracy.
This greatly improves the stability of the delay when the servo is
correcting a large offset.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
When peer delay is < min_neighbor_prop_delay the port is flagged
as non 802.1AS capable. min_neighbor_prop_delay defaults to -20ms.
Signed-off-by: Delio Brignoli <dbrignoli@audioscience.com>
Previouly the peer delay was not taking into account the
frequency offset between the local clock and the peer's clock.
Reset neighborRateRatio to 1.0 in port_nrate_initialize().
Signed-off-by: Delio Brignoli <dbrignoli@audioscience.com>
Richard Cochran
Miroslav Lichvar
Jiri Benc
Delio Brignoli