Add attribute maxStepsRemoved which is included in IEEE1588-2017 (v2.1)
It is an optional attribute which can decide if an Announce message is
considered in the operation of the BMCA or not.
Signed-off-by: Anders Selhammer <anders.selhammer@est.tech>
There is no need to keep two copies of the data set comparison
function. This patch adds a method that allows the port code to
obtain the function from the clock code.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
The function clock_check_ts() performs open-coded manipulation of a
struct timespec instead of using the tmv_t abstractions.
Use the existing tmv_t abstractions to convert from struct timespec to
nanoseconds, and modify the prototype of clock_check_ts() to match
that of the underlying clockcheck_sample().
Signed-off-by: Michael Brown <mbrown@fensystems.co.uk>
The NetSync Monitor protocol will require us to report the time stamp of
the last synchronization. This patch adds new the method.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
As part of the NetSync Monitor protocol, the port will need to have
access to the current data set. This patch adds the appropriate
function.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Separate required_modes setting from clock_create so we can obtain the
required time stamping flags from other place.
Add enum timestamping in struct clock to store the time stamping mode.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
With rtnl socket we can track link status per port(except UDS port).
We can make sure we get the correct interface and latest status with function
port_link_status().
At the same time we need to set clock sde after link down. But we return
EV_FAULT_DETECTED in port_event(), which will not set clock sde. So we need
to set it in port_link_status().
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
The code that determines the index of the PHC device is useful to all
kinds of clock devices.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
This function will allow the TC code to iterate over the ports without
calling into the clock logic.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
The port code is not interested in the number of ports but rather the
clock type. Since the polymorphic clock object will be able to report
its own type, this patch changes the clock interface accordingly.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
There is no need for the 'ifaces' parameter since the list of network
interfaces is already present in the configuration.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
With the new configuration API, there is no need to pass the default data
set. Instead, the clock code can read the configuration directly. This
patch simplifies the clock create method by removing the 'dds' parameter
and moving the code that initialized the data set into the clock module.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
This function allows the ports to read configuration variables without
changing the port method signatures.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
This will help us to simplify the passing of parameters between the main
program. clock, and ports.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Introduce a time stamp processor for offset/delay calculations and use
it in the clock and port modules.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Convert time stamps to tmv_t and apply all corrections before passing
them to clock/port functions to reduce the number of parameters.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
When switching clock devices in JBOD mode, we need to be able to reset the
servo. The existing servo_reset() function will not serve us well, because
in this case we also need to seed the existing frequency offset and limit.
This patch adds a new method that simply starts the servo from scratch.
In the unlikely event of a resource allocation failure, the method will
simply continue to use the previous device, which is better than nothing
and certainly preferable to bailing out the program.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Remove the limit of MAX_PORTS ports (default 8) and keep the ports in
a linked list. This allows ptp4l to be used on large machines and in the
future, it will allow dynamic adding and removing of ports while ptp4l is
running.
For this to work, pollfd needs to be dynamically allocated. Changed pollfd
handling from clock_install_fda/clock_remove_fda to notification
(clock_fda_changed), where the clock will rebuild pollfd by querying all its
ports.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Split management message creation to more fine-grained functions to allow
notification messages to be created.
The new clock_management_fill_response is called from
clock_management_get_response (so the function behaves exactly the same as
before this patch) and from a new clock_notify_event function. The
difference is clock_management_get_response uses the request message to
construct the reply message, while clock_notify_event constructs the reply
message based on the notification id.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
This puts groundwork for event subscription and notification. The individual
events are added by subsequent patches.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
With the new linreg servo the frequency offset and time offset are
controlled separately. The ratio between master's frequency and the
current frequency of the local clock is known and can be used when
calculating delay or peer delay to improve their accuracy.
This greatly improves the stability of the delay when the servo is
correcting a large offset.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Check the sanity of the synchronized clock by comparing its uncorrected
frequency with the system monotonic clock. When the measured frequency
offset is larger than the value of the sanity_freq_limit option (20% by
default), a warning message will be printed and the servo will be reset.
Setting the option to zero disables the check.
This is useful to detect when the clock is broken or adjusted by another
program.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Management messages can cause a change in the clock quality. If this
happens, then it is time to run the Best Master Clock algorithm again.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
New clock options should go into 'struct default_ds' so that we can avoid
growing clock_create indefinitely.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Add new options to ptp4l and phc2sys to print summary statistics of the
clock instead of the individual samples.
[ RC - Fix () function prototype with (void).
- Use unsigned for sample counter.
- Fix over-zealous line breaks. ]
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Adds struct containing clock description info that will be needed for
USER_DESCRIPTION and CLOCK_DESCRIPTION management messages.
Signed-off-by: Geoff Salmon <gsalmon@se-instruments.com>
Reforming the data structure in this way will greatly simplify the
implementation of the management message for this data set.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reforming the data structure in this way will greatly simplify the
implementation of the management message for this data set.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
this patch allows each port to maintain its own pod structure since it is only
used in ports. This will allow the user to configure any special settings per
port. It takes a copy of the default pod, and a future patch will allow the
configuration file to set per-port specific changes
-v2
* Minor change to fix merge with previous patch
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
this patch modifies the ptp4l.c and config settings so that the iface list is
inside the cfg_settings structure
-v2
* Moved "struct interface" into config.h
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
The current code for the timestamping mode does not allow interfaces to have
separate timestamping modes. This is (probably) due to hardware timestamping
mode being required on all ports to work properly.
This patch removes the timestamping field in the struct iface, and makes it a
clock variable which is really what the mode does anyways. Ports get passed
the timestamping mode but no longer appear as though they are separate.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
This commit only adds support for forwarding the management messages.
The actual local effects of the management commands still need to be
implemented.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
If the new ethtool operation is supported, then use it to verify that the PHC
selected by the user is correct. If the user doesn't specify a PHC and ethtool
is supported then automatically select the PHC device.
If the user specifies a PHC device, and the ethtool operation is suppported,
automatically confirm that the PHC device requested is correct. This check is
performed for all ports, in order to verify that a boundary clock setup is
valid.
The check for PHC device validity is not done in the transport because the
only thing necessary for performing the check is the port name. Handled this
in the port_open code instead.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Anders Selhammer
Rafaël Carré
Richard Cochran
Michael Brown
Hangbin Liu
Miroslav Lichvar
Jiri Benc
Geoff Salmon
Jacob Keller