Reforming the data structure in this way will greatly simplify the
implementation of the management message for this data set.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reforming the data structure in this way will greatly simplify the
implementation of the management message for this data set.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
The phyter offers one step sync transmission, but it alters the UDP
checksum by changing the last two bytes, after the PTP payload. While this
is only standardized for IPv6, we will go with it for IPv4 as well, since
the phyter is the only hardware out there.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
The Linux kernel supports a hardware time stamping mode that allows
sending a one step sync message. This commit adds support for this mode
by expanding the time stamp type enumeration. In order to enable this
mode, the configuration must specify both hardware time stamping and set
the twoStepFlag to false.
We still do not support the one step peer delay request mechanism since
there is neither kernel nor hardware support for it at this time.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
We use the PTP_SYS_OFFSET ioctl method in preference to doing
clock_gettime from user space, the assumption being that the kernel space
measurement will always be more accurate.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
In order to set the scope id, we will need to know the interface index
before sending, in some cases.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
It is safer and more correct to clear the addresses before use. The IPv6
fields flowinfo and scope_id in particular should not be set to random
values from the stack.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
this patch uses the new sk_get_ts_info data to check whether the selected
timestamping mode is supported on all ports. This check is not run if the port
data isn't valid, so it will only fail if the IOCTL is supported. This allows
for support of old kernels that do not support the IOCTL to still work as expected.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
this patch changes sk_interface_phc to sk_get_ts_info, by allowing the function
to store all the data returned by Ethtool's get_ts_info IOCTL in a struct. A new
struct "sk_ts_info" contains the same data as well as a field for specifying the
structure as valid (in order to support old kernels without the IOCTL). The
valid field should be set only when the IOCTL successfully populates the fields.
A follow-on patch will add new functionality possible because of these
changes. This patch only updates the programs which use the call to perform the
minimum they already do, using the new interface.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
- fail on unknown options, bad values and other syntax errors
- fail with more than MAX_PORTS ports
- remove implicit global section
- add error messages
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
It seems with some cards the current default of 2 is too small, increase
the number to prevent users from having to investigate the EAGAIN error
messages.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Now that the code automatically falls back to transport-specific time
stamping, this option is no longer needed.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Jiri Benc <jbenc@redhat.com>
Start with the most general HWTSTAMP option. If that fails, fall back
to the option that best fits the interface's transport.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Jiri Benc <jbenc@redhat.com>
Make it easier to find out the compiled-in defaults in the code
and set all options in default.cfg.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
this patch modifies the pi servo to add a configurable max offset (default
infinity). When ever the detected offset is larger than this value, the clock
will jump and reset the servo state. The value of this feature is for decreasing
time to stabalize when clock is off by a large ammount during late running. This
can occur when the upstream master changes, or when the clock is reset due to
outside forces. The method used to reset clock is simply to reset the pi servo
to the unlocked state.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
passing a string as the servo type seems ugly when there are only a few
choices. This patch modifies the servo_create to take an enum instead.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Richard Cochran
Jacob Keller
Miroslav Lichvar