Now the ts label will be either the bond active slave or the interface
name, which is the exactly interface we need to get ts info.
When the link down/up or there is a fail over and ts_label changed, the
phc index may also changed. So we need to check get new ts info and check
clock_required_modes. We will set the link to LINK_DOWN by force if
the new ts_label's timestamp do not support required mode.
If all good, then we set phc index to new one. Also sync clock interval
after switch phc.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Besides link up and down, we may also receive other rtnl messages, like
bond slave changed info, which link state keeps the same.
So we should return EV_FAULT_CLEARED only when both LINK_UP and
LINK_STATE_CHANGED.
When the link state keep the same, we should return EV_NONE.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Update function rtnl_link_status to get bond slave info. Pass the slave index
to call back functions. i.e. port_link_status.
Also check the interface index of rtnl message in function rtnl_link_status.
Then we don't need to check it in port_link_status.
Add ifndef IFLA_BOND_MAX in case we build linuxptp on kernel before v3.13-rc1.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
The previous function use general message and will dump all interfaces'
information. Now update with ifinfomsg so we could get specific interface's
information.
We still could get all interfaces' info if set device to NULL.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
With rtnl socket we can track link status per port(except UDS port).
We can make sure we get the correct interface and latest status with function
port_link_status().
At the same time we need to set clock sde after link down. But we return
EV_FAULT_DETECTED in port_event(), which will not set clock sde. So we need
to set it in port_link_status().
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
The sequence of port_nrate_calculate() and tsproc_update_delay()
in port_peer_delay() is mixed up.
The peer delay depends on the nrate ratio so the nrate ratio
shall be updated before peer delay is calculated.
Signed-off-by: Burkhard Ilsen <burkhardilsen@gmail.com>
This global function used to return an error code, but now it always
returns zero. This patch converts the function signature to return void
and simplifies the main clock loop by removing the useless test.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
The state machines in 1588 do not specify an event that causes a transition
out of the initializing state. This was left as a local issue. For this
transition, the current code assigns the next state outside of the FSM. But
doing so prevents an alternative FSM to handle this transition differently.
By introducing a new event, this patch places this transition where it
belongs, namely under the control of the FSM code,
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Although leaving the INITIALIZING state and clearing the FAULTY state
ASAP both result in a port entering the LISTENING state, still there
is no benefit from conflating the two. In the FAULTY case, the
current code actually skips the INITIALIZING state altogether.
This patch separates the two cases resulting in two benefits. First,
the check for ASAP fault status is only made when a fault is actually
present, unlike the present unconditional check. Second, this change
will allow us to cleanly support alternative state machines later on.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
The code that decides whether a fault qualifies for ASAP treatment is
a tangle of logical operators. This patch replaces the open coded
logic with a helper function whose name makes the intent clear. This
is a cosmetic change only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Looking at the fault logic in port_dispatch(), you might think that
the function, fault_interval(), checks whether a fault is active, but
you would be wrong, since that function always returns zero.
This patch removes the superfluous input error checking inside of
fault_interval() and changes the return type to void, making the
actual behavior explicit. Dropping the input check is safe because
that function has exactly two callers, both of whom always provide
valid inputs.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
If a non-slave port on a boundary clock see an announce message, then it
must decide whether it should take on the MASTER or the PASSIVE role. When
the GM fields from the local clock are identical to those in the announce,
then the sender/receiver ports are used as a tie breaker.
Following a typographical error in 1588, the code wrongly uses the port
identity of the upstream parent as the "receiver" id. As a result, a port
that should be PASSIVE may choose MASTER instead. This patch fixes the
code to use local port id.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
During the configuration rework, the announce span was wrongly converted
into a hard coded macro. In addition, the announceReceiptTimeout option
inadvertently became non-zero for the UDS port. As a result, the UDS port
sets a useless announce message timer, causing the code to close and reopen
the UDS port every few seconds.
This bug has an interesting history. It was first reported and fixed in
commit f36af8e0 ("uds: disable the accidentally enabled announce timer.").
That very fix was wrongly removed in commit 54f45063 ("port: change
'announce_span' into a macro."). Because of various code changes, this
bad commit cannot be simply reverted now.
This patch re-introduces the 'announce_span' variable and clears both it
and 'announceReceiptTimeout' for the UDS port, effectively disabling the
announce message timer.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
The port code is not interested in the number of ports but rather the
clock type. Since the polymorphic clock object will be able to report
its own type, this patch changes the clock interface accordingly.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
The message lists are implemented using a TAILQ from queue(3). The heads
of the list must be initialized using the provided macros, since the field
called 'tqh_last' is non-zero in the initial state. This patch fixes a
potential null pointer dereference by properly initializing the queues.
Note that there is no actual bug in the current code, because it uses the
lists in such a way as to initialize 'tqh_last' before any dereference.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Upgrade the message level to info so the user can see it, but print it
at most once per 5 minutes to not spam the syslog too much.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
The draft Enterprise Profile [1] specifies a hybrid E2E delay mechanism,
where the delay response message is sent "in kind". That is, if the
request is unicast, then the response is also unicast. Apparently this
scheme is already in widespread use in some industries. Also, it makes
sense, because those messages are of no interest to the other slaves in
the PTP network.
Because of the address work already in place, in turns out that adding
this mode is almost trivial. This patch introduces an "hybrid_e2e" option
that enabled the new mode.
1. https://datatracker.ietf.org/doc/draft-ietf-tictoc-ptp-enterprise-profile
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Buggy or mis-configured masters can place bogus logMessageInterval values
in their delay response messages. This patch places reasonable limits on
the range of values that we will accept.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
The logMessageInterval field has an improbable range from 2^-128 to 2^127
seconds. The extreme ends cause an integer overflow in the calculation
of the "foreign master time window". Buggy or mis-configured foreign
masters advertising extreme values will cause incorrect announce message
aging.
This patch fixes the issue by adding thresholds for the bogus extremes.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
This conversion is not straightforward due to the fact that these options
can take a value of "ASAP" or a number. We check for the special ASAP
case in a helper function and leave the numbers to the generic code.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Add new time stamp processing modes to return raw delay and offset based
on the raw delay instead of the long-term filtered delay, and to return
also a weight of the sample. The weight is set to the ratio between the
two delays. This gives smaller weight to samples where the sync and/or
delay messages were delayed significantly in the network and possibly
include a large error.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Hangbin Liu
Burkhard Ilsen
Richard Cochran
Miroslav Lichvar